Installing Bash-2.05a

Estimated build time:           3 minutes 
Estimated required disk space:  20 MB

Installation of Bash

Before you attempt to install Bash, you have to check to make sure your distribution has the /usr/lib/libcurses.a and /usr/lib/libncurses.a files. If your host distribution is an LFS system, all files will be present if you followed the instructions of the book version you read exactly.

If both of the files are missing, you have to install the ncurses development package. This package is often called something like ncurses-dev. If this package is already installed, or you just installed it, check for the two files again. Often the libcurses.a file is (still) missing. If so, then create libcurses.a as a symlink by running the following commands as user root:

cd /usr/lib &&
ln -s libncurses.a libcurses.a

Now we can continue. Install Bash by running the following commands:

./configure --enable-static-link --prefix=$LFS/usr \
   --bindir=$LFS/bin --with-curses &&
make &&
make install &&
cd $LFS/bin &&
ln -sf bash sh

If the make install phase ends with something along the lines of

install-info: unknown option `--dir-file=/mnt/lfs/usr/info/dir' 
usage: install-info [--version] [--help] [--debug] [--maxwidth=nnn] 
	[--section regexp title] [--infodir=xxx] [--align=nnn] 
	[--calign=nnn] [--quiet] [--menuentry=xxx]
	[--info-dir=xxx] 
	[--keep-old] [--description=xxx] [--test]
	[--remove] [--] filename 
make[1]: *** [install] Error 1 
make[1]: Leaving directory `/mnt/lfs/usr/src/bash-2.05a/doc' 
make: [install] Error 2 (ignored)

then that means that you are probably using Debian, and that you have an old version of the texinfo package. This error is not severe by any means: the info pages will be installed when we recompile bash dynamically in chapter 6, so you can ignore it.

When we tested it with the latest Debian version, the last two commands were executed because the install process didn't return with a value larger than 0. But you would do good to check if you have the $LFS/bin/sh symlink on your LFS partition. If not, run the last two commands manually now.

Command explanations

--enable-static-link: This configure option causes Bash to be linked statically

--prefix=$LFS/usr: This configure option installs all of Bash's files under the $LFS/usr directory, which becomes the /usr directory when chroot'ed or reboot'ed into LFS.

--bindir=$LFS/bin: This installs the executable files in $LFS/bin. We do this because we want bash to be in /bin, not in /usr/bin. One reason being: the /usr partition might be on a separate partition which has to be mounted at some point. Before that partition is mounted you need and will want to have bash available (it will be hard to execute the boot scripts without a shell for instance).

--with-curses: This causes Bash to be linked against the curses library instead of the default termcap library which is becoming obsolete.

It is not strictly necessary for the static bash to be linked against libncurses (it can link against a static termcap for the time being just fine because we will reinstall Bash in chapter 6 anyways, where we will use libncurses), but it's a good test to make sure that the ncurses package has been installed properly. If not, you will get in trouble later on in this chapter when you install the Texinfo package. That package requires ncurses and termcap can't reliably be used there.

ln -sf bash sh: This command creates the sh symlink that points to bash. Most scripts run themselves via 'sh' (invoked by the #!/bin/sh as the first line in the scripts) which invokes a special bash mode. Bash will then behave (as closely as possible) as the original Bourne shell.

The &&'s at the end of every line cause the next command to be executed only if the previous command exists with a return value of 0 indicating success. In case all of these commands are copy&pasted on the shell, is is important to be ensured that if ./configure fails, make isn't being executed and, likewise, if make fails, that make install isn't being executed, and so forth.

Contents of bash-2.05a

Program Files

bash, sh (link to bash) and bashbug

Descriptions

bash

Bash is the Bourne-Again SHell, which is a widely used command interpreter on Unix systems. Bash is a program that reads from standard input, the keyboard. A user types something and the program will evaluate what he has typed and do something with it, like running a program.

bashbug

bashbug is a shell script to help the user compose and mail bug reports concerning bash in a standard format.

sh

sh is a symlink to the bash program. When invoked as sh, bash tries to mimic the startup behavior of historical versions of sh as closely as possible, while conforming to the POSIX standard as well.

Dependencies

Bash-2.05a needs the following to be installed:


bash: bash, sh
binutils: ar, as, ld, ranlib, size
diffutils: cmp
fileutils: chmod, cp, install, ln, ls, mkdir, mv, rm
gcc: cc, cc1, collect2, cpp0, gcc
grep: egrep, grep
make: make
gawk: awk
sed: sed
sh-utils: basename, echo, expr, hostname, sleep, uname
texinfo: install-info
textutils: cat, tr, uniq